If the apartment is cold in winter, most likely you need a replacement radiator. Traditional cast iron or steel batteries become dirty over time.
The coolant moves along old appliances in a thin stream, does not provide thermal energy sufficient for normal heating of the home. To improve the thermal regime, it is worth dismantling the old equipment and installing new ones, but for the best result, you need to know how to correctly perform the work.
In this material we will talk about how to properly dismantle old radiators and install new devices in their place.
What needs to be thought out in advance?
If the decision to carry out repairs of this type is made, you should find answers to a number of questions:
- When and by whom will the work be carried out?
- What type of radiator should I use?
- Is it necessary to replace pipes leading from the battery to the riser?
- How many sections will each room need?
It is best to carry out such an alteration in the summer, because to start work, you must obtain the permission of the local housing office. In winter, officials give such permits extremely reluctantly because they will have to block the common riser and leave other apartments without heating for some time.
But even outside the heating season, getting permission can be difficult. Those who have already solved such problems speak of the need to wait several days, trying to get an appointment with the right employees, etc. Some were faced with pressure: they were recommended to hire plumbers from the housing office to carry out all the work.
There are no restrictions on this issue. The main thing is that the replacement of the heating batteries is performed by an experienced plumber with the appropriate qualifications. It is possible to identify all the flaws made during inept installation only during operation.
Old radiators become dirty inside and out over time, cleaning does not always help to solve the problem of insufficient heating, replacement is a more efficient option
It is best to go to the Housing Office in the summer, and not in the fall, which accounts for the peak of lines. At this point, all the necessary materials must be purchased, pre-assembled radiators, prepared tools, negotiated with the team, if necessary.
If the house is connected to a central heating system, you should contact the service department to agree on a remake. Here you can perform the necessary calculations to accurately name the number of sections of radiators, as well as clarify other technical issues.
You can calculate the required number of heating radiators yourself. How to do this we described in detail in this article.
Shut-off valves, which are installed on the “supply” and “return”, are necessary so that at any time it is possible to shut off the water and remove the battery for repair or replacement
Lack of proper calculations can lead to an imbalance in the home heating system.
First, for the calculations, you need the information that is in the DEZ:
- type of boiler room (it can be central or individual for a particular house);
- type of system: two- or single-tube;
- parameters of existing supply pipes;
- coolant characteristics: temperature, pressure, pH, etc.
Most often, old batteries are replaced with new modern models, usually aluminum or bimetal. Although cast iron, copper and steel products are also available. The type of radiator is needed when performing calculations.
When choosing a suitable radiator for a house or apartment, it is necessary to focus on its main characteristics, which are detailed in the product data sheet
Such indicators as pressure which the device can take out, the maximum temperature of the heat carrier, heat transfer and other data will be required. They can usually be found in the technical data sheet.
If not only radiators, but also pipes leading to them are subject to replacement, you should choose the appropriate material. Usually it is steel, metal-plastic or polypropylene. Some wizards strongly recommend using only steel communications for centralized systems.
Depending on the type of pipe chosen, appropriate equipment for their welding will be needed. MP and PP pipes are easier to mount than steel. To work with metal, you need not only a welding machine, but also a tool for threading. Therefore, if the old pipes are clean enough, it is recommended to leave them, and replace only the battery.
Old cast-iron radiators retain heat well, but slowly give it away, in addition, they are heavy, which complicates installation, so bimetallic and aluminum models are more popular
The weak point of metal-plastic constructions is joints. They must be performed very carefully, installation errors often lead to leaks. The popularity of MP pipes is explained by their relatively low price. Plastic is more expensive, but more reliable, if the welding is done correctly, the tightness of the joints will be very high.
For the selected radiator, you need to choose the appropriate fasteners. In this case, it is necessary to take into account both the type of radiator and the material of the wall on which the installation will be performed: brick, concrete, etc. Typically, batteries are equipped with the appropriate type of bracket.
To install one radiator, usually use two brackets at the top and one at the bottom. Their position is carefully checked by the level, so that during the installation of the battery to eliminate the possibility of bias. However, some models are installed with a slight slope to ensure the removal of air entering the system. If the number of sections is more than twelve, you may need another top bracket.
Rules for placing a radiator
Batteries are placed most often under the window to compensate for heat loss when cold air enters through the opening.
In this case, the following distances must be maintained:
- from the wall - 20 mm;
- from the floor - 120 mm;
- from the windowsill - 100 mm or more.
It is advisable that the window sill does not overlap the radiator too much for efficient air circulation in the room. These figures are only recommendations, they can be more or less, although noticeable changes can affect the heat transfer of the structure.
The heat dissipation of the battery may vary depending on the installation method. If the distances are maintained correctly, the device will give off more heat.
To improve the situation, it is recommended to cover the wall behind the radiator with reflective material, such as penofol. Although some masters consider this measure useless. But a beautiful decorative screen will become an obstacle to warm air, it is better to refuse it. Modern batteries look quite attractive, it makes no sense to hide them.
The order of work
To correctly replace the heating radiators in the apartment, you must:
- Align the alteration with the service department.
- Purchase the necessary materials.
- Preassemble nodes.
- Prepare the tools.
- Agree with the team (if it is not planned to do the work yourself).
- Make alteration in the housing office, to determine the date of work.
- Remove old radiators.
- Install the brackets.
- Attach new batteries.
- Connect to the heating pipes.
- Check system operation.
During the preliminary assembly of the nodes, all the necessary elements are installed: plugs, gaskets, Mayevsky cranes, etc. In addition, you can pre-mark in those places where the pipes will be cut. In this case, a plumb line and level should be used so that the new radiator becomes level.
If the supply pipes also require replacement, these elements must also be prepared: cut pieces of suitable length, attach tees, etc. All this is done in order to quickly complete the installation after draining the water from the heating system. Such a measure will be more than relevant if the need to replace old batteries arose during the heating season.
Welding is used to replace metal pipes. Threads will need to be cut at the edges of the structures to reliably connect them to the radiator
The procedure for dismantling old batteries depends on whether the pipes need to be replaced. If you need to keep the supply communications, you will have to carefully unscrew the old battery. At the same time, it is important to maintain the flare - a sufficiently long thread at the edge of the pipe. The radiator is fixed with a nut and a coupling, which will have to be unscrewed.
The procedure can be quite complicated. If the parts do not move, you can try to loosen the connection with anti-corrosion compounds. In the worst case, the radiator is simply cut off by a grinder. At least 10 mm of thread must remain. Deburrs should be removed from it.
If you decide to leave the old steel pipes, then the radiator must be dismantled carefully so that the threads on the bends remain intact
If it was not possible to maintain the flare, it will be necessary to build up the pipes, as well as cut new threads. The removed locknuts can later be reused when installing a new radiator. It is much easier to dismantle the radiator if the pipes are also replaced. In this case, they are simply cut off in a suitable place. Usually this is the place where the system turns to the neighbors above and below.
Now you need to install the brackets, and then hang a new radiator on them. At this stage, sometimes it is necessary to adjust the length of the supply pipe. It remains to restore the threaded connection. It is very important to properly seal. For this, flax or plumbing thread is usually used.
Some masters do not recommend using FUM tape on such connections. The sealant is wound clockwise so that it forms a cone growing from the edge of the thread. Then screw the union nut. If part of the seal is left outside, this is normal. But its layer should not be too thick.
Such work generates a lot of garbage. They are best produced during major repairs, after the windows are installed.
In order to achieve maximum tightness, sometimes the sealant is impregnated with paint, after which a lock nut is screwed. Then the protruding insulation is also impregnated with paint. Aqueous emulsion composition for these purposes is not suitable. After the paint has dried, it is very difficult to loosen the joint.
At the end of the connection, remove the protective film from the radiator. You must also check the position of the air vent. Its opening should be directed upwards. To check the quality of work, you need to ask the plumbers to pump water into the heating circuit under pressure.
It is better to remove the film in which the new radiator is packaged after it is installed so as not to accidentally damage the coating
This will allow you to identify and immediately eliminate leaks. During operation, it does not hurt to watch the radiator for the first time, as well as check the condition of the connections to make sure that they do not leak.
Some interesting tips
If you decide to change the old batteries, it does not hurt to think about installing a faucet, normal or with a thermal head. In the first case, you can manually adjust the flow of coolant, in the second - this will be done automatically. But if a thermostat was installed on the radiator, it does not need to be covered with a decorative screen.
The thermal head on the shut-off valve allows you to change the amount of coolant so that the temperature in the room is always high enough
This will lead to data distortion during temperature measurements. It is worth noting that thermostats can be set only with single-pipe systems. In any case, at least one stopcock should be installed at the inlet and outlet of the radiator, if they are missing.
This will disconnect the radiator from the system to clean or replace it, regardless of the season. The thermal power reflected in the battery data sheet does not always correspond to the declared one. If you make the number of sections 10% larger, you can improve the situation.
How to choose a suitable replacement option:
Detailed master class:
Overview of common errors:
Inexperienced masters should not start practicing on heating systems. In the process of replacing one radiator with another, there are many nuances. Errors will result in costly repairs. It is better to entrust such a task to experienced plumbers.
If you have experience in self-replacement of heating radiators, please share it with our readers. Perhaps you know the subtleties that we did not mention in this article? Tell us about them in the comments section.